Architecture Tools
Browse all available architecture tools.
Available tools
- Acoustic Panel Edge Shadow Gap Tool Calculate acoustic panel edge shadow gap from explicit caller-supplied inputs.
- Arch Intrados Extrados Radius Gap Tool Radial thickness between supplied concentric arch surfaces, with an explicit signed measurement correction.
- Arch Segment Radius From Rise Span Tool Find the circular-arch radius from chord span and positive sagitta in matching length units.
- Architecture: Door Leaf Clearance Hinge Offset Tool Project a zero-thickness door leaf outer edge about an explicitly offset hinge axis in plan; not a clearance, accessibility or building-code certification.
- Balcony Guard Gap Explicit Clearance Tool Compare a measured gap with an explicit caller-supplied limit; the calculation does not select a regulation.
- Brick Bond Half Module Offset Tool Calculate brick bond half module offset from explicit caller-supplied inputs.
- Cavity Wall Insulation Net Area Tool Calculate cavity wall insulation net area from explicit caller-supplied inputs.
- Ceiling Void Clear Height Tool Resolve the ceiling-service void from measured soffit height, desired occupied clear height and ceiling thickness. Negative clearance reports a geometric conflict.
- Curtain Wall Panel Spandrel Share Tool Calculate curtain wall panel spandrel share from explicit caller-supplied inputs.
- Door Leaf Undercut Area Term Tool Calculate door leaf undercut area term from explicit caller-supplied inputs.
- Door Undercut Finish Floor Gap Subtract an explicit finished-floor elevation from a door-bottom elevation on the same datum without setting clearances.
- Drawing Elevation Datum Offset Tool Place a drawing elevation on a shared absolute vertical datum using the supplied drawing-zero elevation.
- Facade Joint Open Width Thermal Delta Subtract an explicitly supplied signed thermal closing displacement from joint width without estimating expansion or code compliance.
- Facade Module Remainder Tool Return one residual facade width after supplied modules and explicit internal/edge joints.
- Facade Opening Solid Share Tool Split a facade's gross area into nonoverlapping opening and solid shares.
- Facade Solar Fin Projected Depth Tool Project a fin depth perpendicular to a supplied ray direction in a planar section, with angle in radians.
- Floor Screed Taper Average Thickness Tool Calculate floor screed taper average thickness from explicit caller-supplied inputs.
- Glazed Facade Mullion Area Share Tool Deduct overlapping rectangular full-span mullions once when estimating a regular facade frame fraction.
- Glazing Frame Sightline Offset Subtract an explicit frame-edge coordinate from the visible glazing edge on the same section axis.
- Lintel Bearing Seat Length Calculate equal end-seat lengths from explicit centered lintel and opening widths, preserving a shortfall without structural assessment.
- Masonry Course Height Module Calculate an explicit masonry course module and stack height with joints only between units.
- Masonry Opening Arch Ring Area Tool Calculate masonry opening arch ring area from explicit caller-supplied inputs.
- Opening Reveal Area Factor Tool Calculate opening reveal area factor from explicit caller-supplied inputs.
- Parapet Coping Drip Edge Extension Tool Calculate parapet coping drip edge extension from explicit caller-supplied inputs.
- Pitched Roof Eave Horizontal Projection Tool Calculate pitched roof eave horizontal projection from explicit caller-supplied inputs.
- Ramp Landing Length Residual Tool Compare a measured landing length with an explicit requirement without selecting a building-code threshold.
- Ramp Landing Net Run Allocation Tool Subtract explicit horizontal landing lengths from the allocated ramp run without choosing a building-code limit.
- Roof Pitch Clearance Point Tool Evaluate one ideal roof-line point from supplied dimensions without a structural or code-compliance assessment.
- Roof Pitch Rise Per Run Label Tool Label a nonnegative roof pitch with explicit rise and positive horizontal run in consistent length units.
- Roof Plane Height Sample Tool Calculate roof plane height sample from explicit caller-supplied inputs.
- Roof Valley Line Slope Component Resolve an explicit roof-valley line slope and horizontal run into signed rise and sloped length without deriving intersecting roof geometry.
- Roof Valley Plan Diagonal Factor Tool Calculate roof valley plan diagonal factor from explicit caller-supplied inputs.
- Room Diagonal Clearance Two Sides Tool Return the diagonal clear span of a rectangular room from its two perpendicular clear sides.
- Room Dimension Clear Structural Crosswalk Subtract explicit opposing finish build-ups from a structural span, preserving over-occupation as a negative clear span.
- Room Net Gross Area Ratio Tool Return room net-to-gross area and its reciprocal using explicitly comparable measured area boundaries.
- Room Skirt Board Door Deduction Tool Calculate room skirt board door deduction from explicit caller-supplied inputs.
- Slab Level Finish Build Up Tool Add a nonnegative finish build-up to a structural slab elevation in consistent vertical units.
- Soffit Slope Clearance At Point Tool Signed clearance under an explicitly supplied linear soffit profile.
- Stair Landing Door Swing Overlap Tool Area accounting from a supplied swing/landing intersection; no door-clearance rule is selected.
- Stair Nosing Projection Label Tool Label a measured stair-nosing projection in millimeters without assigning building-code compliance.
- Stair Riser Count Adjusted Rise Divide an explicit finish-corrected stair rise into equal risers without choosing counts or checking building codes.
- Stair Winder Inner Tread Gap Tool Compare equal radial winder arc widths with an explicit supplied minimum, without selecting a code.
- Stair Winder Walking Line Tread Term Tool Calculate stair winder walking line tread term from explicit caller-supplied inputs.
- Vault Semicircular Rise Span Check Tool Calculate vault semicircular rise span check from explicit caller-supplied inputs.
- Wall Center Line To Face Offset Tool Locate a symmetric wall face from its centerline, thickness and explicit signed side along one coordinate axis.
- Wall Layer Reference Plane Offset Tool Locate a plane by supplied layer order and distance from the selected layer face.
- Wall Layer Vapor Resistance Term Tool Compute supplied vapor diffusion resistance factor times layer thickness, without predicting condensation.
- Wall Opening Net Masonry Panel Area Subtract an explicit total nonoverlapping opening area from a rectangular wall-panel area without assessing structural design.
- Window Clear Opening Frame Deduction Tool Calculate window clear opening frame deduction from explicit caller-supplied inputs.
- Window Reveal Depth Reference Subtract an explicit wall reference coordinate from the window face on a shared depth axis.
- Window Wall Projection Ratio Tool Compare orthogonal projected areas under supplied direction cosines; no building-code check.